Basic Boat Info
Dimensions
Engines / Speed
- Make: Cummins
- Model: 6BT5.9M
- Drive Type: Direct
- Fuel: Diesel
- Engine Power: 180hp
- Type: Inboard
- Engine Hours: 3927
- Engine Location: Center
Tanks
Other
Accommodation: 8 Guests +3 in:
1 x Queen Double
2 x Single berths + Pullman
2 x Single berths+ Pullman
1 x Double + Pull out
Crew: 3 x Single berths + 1 x sofa
Fuel 2,135 litres / 496 US gals in 4 x stainless steel tanks
Extra Fuel capacity 335 litres / 88 US
Water 930 litres /246 US gals
Hot Water 80 litres /13 US gals
Holding tanks 270 litres 71 US gals
Black Water: 110 litres / 29 US gals in 2 x stainless steel tanks
Additional Black Water: 55litres / 15US gals in 1 x stainless steel tank
Cruising Speed 9 knots with engine
Range (nm) 1,500 nm approx.
Engine 1 x Marine Cummins D4-180 Diesel 132 kW / 180 Hp at 2,800 rpm, with directmounted reduction gear.
Engine Hours 3,927 hrs (July 2023)
Engine Controls 2 x Spinlock throttles
Gearbox Marine HS45AE 8° down angle
Reduction Gear 2.43:1.
Propellers 1 x4 - Bladed folding propeller Brunton Varifold ø
660 x 470 (26” x 18.5”).
Propeller Shaft Supported by water lubricated rubber bearings at the P-bracket and stern tube. Drip-free shaft seal.
Bowthruster Max-Power, driven by PTO on diesel generator,
Thruster controls on both port and stb wheels.
Steering System Dual steering gear and sheaves
2 x Wheels, 3 turns H.O. to H.O.
Steering wheels are clear coat carbon Exit (The wheels are FRESHLY clear coated – look like new)
Rudder Foam filled carbon fibre/epoxy skins with a tubular carbon fibre stock
Generators & Electricity 1 x Panda 24 NE main generator, 16 kVA 230 V 50 Hz
Diesel; with PTO connected to bow thrusters; mounted in a sound shield on elastic mounts.
Day Generator: 1 x Panda 5000 LPE, 4.7 KVA, including sound shield
Oil handling system: 1 x Gori 400 Oil change pump
24V connected to main engine and generator.
Shore Power Converter 12kVA 170-520 V 50/60 Hz in 230 V 50 Hz out,
including remote touch panel
Starting battery 24 V 50 Ah
Service battery 24 V 1440 Ah
Radio battery, 24 V 290 Ah (20 h)
Shore power 230 V 50 A or 115 V 50 A
Battery Charger 2 x 75 A
Battery charger instruments 1 x 50 A
Emergency Power Back-up power from hydraulic pump on diesel generator to Power Pack- (If batteries do not work)
Converters Conversion of 24 V DC to 230 V AC 50 Hz for single-phase AC consumers
1 x Mastervolt service battery supplied 24/2500 VA for miscellaneous
1 x Mastervolt radio battery 24/1500 VA for instruments and entertainment
A 6kVA used for the shore power in USA.
Separate shore inlet for air conditioning
Chargers 2 x Mastervolt, Mass 24 V 75 A w/ 3-step for service
1 x Mass 24V 50A for the radio battery
Hydraulics Hydraulic system is a Bosch-Rexroth custom
Hydraulic Functions Anchor windlass, Jib Furler, Bow thruster,
Boom vang
Optional Rexroth power pack upgraded with 6
extra functions for hydraulic winches.
Code Zero Furler (CZ8T), inner forestay, jib
halyard, outhaul and backstay.
All hydraulics are push button controlled
Hydraulically controlled transom door/bathing
platform with real teak
Power System 1 x DC electric motor standby pump unit Bosch-
Rexroth A10V028, ~5 kW.
1 x Genset back-up generator PTO pump Bosch-
Rexroth A10V045 on genset.
Bilge Pumps 2 x Bilges in fwd & aft cabins
1 x Bilge in lazarette
Emergency Bilge Pump 3 x Manual Whale Titan 100 l/min (26 US gals) as
Air Conditioning Condaria PCWM/FCL 12002 reverse cycle with unit fitted ECP, supply voltage 230 V 50/60Hz, 50 Hz
Supply & Exhaust System Both with central fan & electrically run Airflow adjusted by main panel
Water Heater 1 x 80 litres heated either with engine cooling
water or with a heating elements working on AC.
City Water Connection Including pressure reducer, connected to pressure water system.
Water Filters 2 x Water charcoal filters for city water inlet
Water Pressure System 1 x System with 2 x Amfa A95, 24V pumps.
1 x 18 litres pressure tank connected to the system.
Toilet System Tecma Silence Standard, 24 V.
Flushing by fresh pressure water.
The function cycle is completely automatic.
Sewage System All toilets are connected to black water tank.
No possibility to flush toilets direct overboard.
Tanks are emptied by 24 V electrical pumps to seacock via siphon breaks. Each tank is also provided with a deck suction line.
Fuel Filter /Water Separator 1 x Dual Separ SWK 2000/5UMK
1 x Single SWK 2000/5MK for generator
Air Compressor 1 x Thompson 24V low pressure (6 bar) piston in the lazarette for the transom door air seal.
Passerelle 1 x Side boarding ladder
1 x Swim ladder (Stored in Lazarette)
Sail Dimensions I: 32.15m
J: 9.04 m
P: 31.33 m
E: 10.40 m
Mainsail: 187.35m2
90% Jib: 127.39 m2
Spinnaker: 469.00 m2
Code 0: 336.10m2
Sails 3Di Mainsail
3Di Genoa
Storm Jib
Storm Trisail
Code Zero
A2 Spinnaker
A4 Spinnaker
Rig
- Spars by Off Shore Spars from standard modulus carbon fibre; painted white.
- 4 x Spreader masthead rig w/ discontinuous shrouds and 18° swept spreaders
- Carbon fibre masthead has Harken sheaves for:
- 2 x Jib halyards,
- 2 x Masthead spinnaker halyards,
- 1 x Mainsail
- 1 x Spare mainsail halyard.
- 1 x Spinnaker halyard has a 2:1 padeye for Code 0.
- Combination staysail/pole lift halyard located under the inner forestay lugs.
- 1 x Lightning strike rod & cable run to the bilge internal wiring, shielded in PVC
- Tubes secured to the mast.
- Boom & boom vang goosenecks are composite fabrications bonded to the mast.
- Water stop installed at the height of the lowest halyard exit.
- Lower spreaders have flag halyard fairleads port and starboard.
- LED spreader lights port and starboard, two each side.
- External track for full-batten mainsail.
- Storm trysail track.
- Offshore Spars carbon instrument bracket for four B&G 30/30 displays on mast.
- Preparation for masthead strop lock for spinnaker halyards.
- Harken 32mm switch track.
Boom
The outboard end has sheaves for two reefs and an outhaul.
The inboard end has sheaves for two reef lines leading to the deck.
A double grooved, clear anodized aluminium track is bonded to the inside perimeter of the boom top. The outer groove can be used for a sun awning and the inside track is used for a mainsail cover
Rig Hydraulic
- Manual hydraulic system but for boom vang low load control hydraulic pressure (up to 2000 psi) from the Power Pack can alternatively be used.
- Four-function one-gauge System 50 central control panel with two-speed pump in aft cockpit for backstay, outhaul, jib halyard, and inner forestay.
- Separate System 50 panel for the boom vang, alternatively low oil pressure can be fedfrom the Power Pack to the vang.
- Cylinders for backstay legs, mainsail outhaul, for jib halyard cylinder on side of mast, andfor inner forestay below deck.
- Boom vang with high-pressure return, and quick release controls both sides in cockpit.
- The hydraulic mast jack will have two 25-ton external, removable cylinders.
- The assembly includes a high-pressure manual pump, gauge, hydraulic hose and quick disconnect. Jacking pressure chart laminated to the mast and also included in the mast manual.
Standing Rigging
- Replaced with Carbon E6.during 2019 Refit
- Carbon E6 Forestay new in July 2023
- Running rigging colour coded Dyneema with Tylaska snap shackles. (Almost brand new .)
- Running backstays - Kevlar (Replaced 2023. A spare set of runners was fabricated at the same time.)
- Quiver of equiplite snatch blocks.
Furling Gear
- Reckmann code 0 furler with top swivel, including one power pack function
Sail Handling System
- Mainsheet deck lead for a single port main sheet on a winch console
- Stainless jib sheet tracks Harken H1888 with Harken C5754 cars and Harken end stops
- 2 x Harken C5754 cars for the stay sail sheets.
- 2 x Harken H3033 double foot blocks for jib and stay sail sheets.
- 2 x Runner blocks Harken H3022 + dead end Harken pad eyes
- 2 x MPS / aft guy block Harken 3022.
- 1 x Main sheet block Harken C7218 low led pivoting + dead end pad eye
- 10 x Harken roller bearing lead blocks for halyards and reef lines at the mast partners
- 4 x Spinlock jammers ZS1618 on port side @ mast for reef lines & halyards
- 3 x Spinlock jammers ZS1618 on stbd side @ mast for reef lines & halyards
- 1 x Spinlock jammer ZS1214 on stbd side @ mast for the topping lift/staysail/halyard
- 1 x Spinlock jammer ZS1214 for the tack line
- 1 x Spinlock jammer for the tackline that is switchable to either side or off completely
Winches & Windlasses
- Capstan drum, Sanguineti Chiavari code 3710400, 2000 W 24 V recessing into deck including two watertight footswitches near the drum.
- Deck changes to accommodate larger primary winches.
- Alternative, with 3-speed mainsheet winch
- Harken hydraulic, alloy winches
- Primary winches 2 x B1111.3 STCAC HY (carbon top and base)
- Secondary winches 2 x B990.3 STR HY AD (carbon top)
- Halyard winches 2 x B990.3 STR HY AD (carbon top)
- Mainsheet 1 x B1111.3 STCAC HY (carbon top and base)
- Antal winch switches instead of standard.
- Lower profile hydraulic motors to gain headroom
Lifelines & Stanchions
- Stanchions, 740 mm high w/ spacing conforming to ISAF/ORC requirements
- Stainless 8 mm wire lifelines, 740 mm high with polished turnbuckles and eyes.
- Gates in lifelines on each side amidships and in the push pit.
Hatches and windows
- Nautor custom made flush mounted tinted acrylic hatches w/gutters and frames.
- Gas cylinders support all hatches.
- Optional storm covers for 4 hatches on foredeck. (MCA item 4).
- Optional front windows to raise saloon
- Fold-up teak seat on pushpit, both sides
- Drains inboard of teak toe rails, two each side
- Automatic anchor windlass winch handle to be extended
- Roller fairleads built into forward legs of pushpit
- 8 x Non standard deck cleats
- 6 x Stainless steel pop-up fairleads, Versari & Delmonte, instead of standard
- Bracket for GPS GP-320B antenna on pushpit
- A deck shower is installed at bathing platform.
2 x Sinks are located in counter inboard.
2 unit Miele Induction Cooker outboard
Microwave oven located in the aft part of the galley.
Waste bin fwd of cooker.
1 x Freezer- located in the aft part of the galley
1 x Fridge - located in the aft part of the galley
1 x Additional fridge is facing aft.
Chest of drawers and stowage for pots & pans in the lower lockers.
Stowage for crockery and glasses in the upper lockers.
General lighting with spotlight down lighting.
Working lights under upper lockers.
1 x 2 Unit Electric Induction Hob
1 x Top loading freezer 170.
Options fitted to galley
- Corian fiddles in galley around counter tops instead of standard teak.
- Icemaker, Raritan 230 V (In saloon)
B&G:
- H3000 Hercules Performance Base Pack - Monochrome BGH 300003 including:
B & G Colour 19” Glass Multi Function Screen at Navigation Station
B & G Colour 18”Glass Multi Function Screen at each Helm Position
Panasonic Tough Book Laptop with Expedition Software
Panasonic Toughbook ‘Deckman type’ Tablet
- Vertical masthead unit 1450 mm, BGH30003.
- Halcyon Gyro-stabilized compass with Halcyon Gyro processor, BGH60001.
- Paddlewheel speed sensor with plastic flanged housing, SEN-SPD-HP.
- Depth sensor with plastic flanged housing, SEN-DPT-HP.
- Barometric pressure sensor, 690-00-007.
- 2 x Additional GFD Hydra displays, BGH210001, one in owner's cabin and one in crew cabin.
- 4 x 30/30 displays, BGH240001, on the mast
- 4 x H3000 FFD Hydra displays, GH200001 two on each side in cockpit.
- 2 x H3000 360deg wind direction display, BGH230002 , one on each side in cockpit.
- 2 x H3000 20/20 display (red backlight) BGH270001, to each side in cockpit.
Other navigation systems
- GPS/WAAS receiver, Furuno GP-320B, connected to Furuno radar/plotter.
- Backup GPS/DGPS/WAAS receiver, Furuno GP-37, display at nav station.
- Navtex receiver Furuno NX-300, including H-field antenna NX-3H-D. Dual frequency receiver (490,518kHz).
- AIS transponder Furuno FA-150 including GPS and AC Marine CX4 VHF antennas.
- Connected to radar/plotter, GPS and VHF antenna.
- Radar system including:
Furuno MU-170C 17" display at nav station
Furuno DRS4D NavNet 3D 4 kW 24" radome scanner positioned in front of mast.
- PC Weatherfax for Windows software including demodulator, connected to SSB and
- computer.
Magnetic Compass 2 x Suunto 5” at helm adjustable for global balancing.
Gyro Compass 1 x Brookes & Gatehouse Halcyon Gyro stabilised compass will be used as the main heading source for the navigation instruments
Barometer 1 x George Jensen clock and barometer
Barometric pressure is displayed in the B&G
H3000 system.
Automatic B&G H3000 ACP2 pilot pack monochrome
BGH300051 including:
- pilot display unit in cockpit GRP-box
- ACP2 computer unit
Rudder reference unit.
Hydraulic constant running pump with twin
hydraulic cylinders
Navigation Lights Stern light LED Lopolight
Port sidelight LED Lopolight.
Starboard side light LED Lopolight.
Steaming light.
Aqua signal 50 fixed masthead anchor light.
Lopo light LED.
Spreader down lights on the lowest spreader,
2 x 20W on both sides.
Spreader lights up & down incl. flood lights- LED white.
Windex light at the top of the mast.
Three boom lights above the cockpit with dimmer.
Flood down lighting on the forward side of the mast.
Bathing platform light integrated with the stern nav light.
SALOON
- Wide screen HD Ready LCD TV 32", Loewe Concept with digital DVB T/C (European) tuner, in saloon. Pop-up lift system PSP-AV P and remote control, for 32" TV in saloon.
- Home Entertainment system with five speakers and woofer in saloon.
- Video and audio from saloon
COCKPIT
- Aft/Fwd cockpit speakers Sony XS MP-1610 connected to Saloon stereo.
- 2 x Power amplifiers and volume controller in cockpit GRP-box.
OWNER'S CABIN
- Wide screen HD Ready LCD TV 26", Loewe Individual 26 Selection with digital DVB-T/C with digital DVB-T/C (European) tuner.
GUEST AND CREW CABINS (4 cabins)
- 4 x Wide screen LCD TV monitor 19" Samsung SynchMaster with analogue PAL/SECAM
- (European) tuner, one in each cabin.
Diving Compressor
- Diving compressor Bauer Junior II – W - 225/300 bar
- Diving gear (Snorkels/ Flippers/Masks)
Crane
- Anchor davit stainless steel mirror polished gas ram launching mechanism for 140 lbs CQR anchor. Including: davit support, open + close position, open position anchor point, anchor fixing system, swivel type roller head, stainless steel gas ram, stainless steel gas ram cam, bushes, waterproof bearings.
Fire fighting system
- Total flooding Clean Agent (FM200) fire extinguishing system for the engine room
space with a manual remote control.
- Two fire hydrants with hose reel, one forward and one aft
- 3 x Portable extinguishers in interior.
Safety Equipment
- Safety belts for navigator and cook
- 2 x Jackstays of webbing
- Stainless steel folding arm,
- 1 x 140 lbs CQR Danforth 60 H (27 kg) anchor stowed below deck.
- 1 x 100 m 12 mm (1/2") high tensile anchor chain (to conform to MCA code)
- 4 x Mooring lines 15 m each, diameter 20 mm.
- 2 x Mooring lines 25 m each, diameter 20 mm.
- 8 x Air fenders with lines.
- 1 x Boat hook stowed below.
- CQR anchor 140 lbs instead of standard 105 lbs
- Anchor chain Lewmar 12 mm, grade 40, 10 meter attached to standard
Danforth anchor
- with standard 100 m anchor line spliced to chain
1 x Side Boarding ladder (stored in stern locker)
1 x Swim Ladder with flush stainless steel fittings + 3 steps under water level is at the transom heck (stored in the lazarette)
- Other equipment
- Owner's Manual in English including manuals supplied by equipment manufacturers in the language(s) provided by such manufacturers.
- The Owner’s Manual contains directions for use, maintenance and winterising as well as drawings and diagrams for main systems.
- Winch handles: two 10" lock-in, two 10" single grip, one ratchet.
- Carbon flagpole, instead of standard.
Nicolle Associates offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.
- As always photographs do not do justice so a viewing is highly recommended.
- This boat is lying in Hong Kong.
- © 2023 Nicolle Associates